全自动凉茬机的使用方法

发布于:2024-05-13 14:13:25  来源:http://www.qfrtrq.com

  全自动凉茬机的使用方法

Usage of fully automatic stubble cooling machine

  全自动晾茬机是将摊晾、加浆、加曲、搅拌、卸料等工序一次性完成,与传统工艺相比,大大降低劳动强度,实现机械自动化。装有多个轴流风机,通过风量的调节,使高温凉茬在输送过程中降到规定的温度,摊晾效果好,在摊晾过程中设置多个搅拌装置,使凉茬在摊晾过程中松散、不易结坨,加浆、下曲均匀,数量可调节,通过装置可将浆水、曲粉、粮茬搅拌均匀。

The fully automatic stubble drying machine completes the processes of spreading, adding pulp, adding yeast, stirring, and unloading in one go. Compared with traditional processes, it greatly reduces labor intensity and achieves mechanical automation. Equipped with multiple axial flow fans, the air volume is adjusted to lower the high-temperature cold stubble to the specified temperature during transportation, resulting in good spreading effect. Multiple mixing devices are set up during the spreading process to make the cold stubble loose and less prone to clumping. The addition of slurry and downward bending are uniform, and the quantity can be adjusted. Through the device, the slurry, koji powder, and grain stubble can be evenly mixed.

  使用步骤:

Usage steps:

  一、安装前应查看全自动晾茬机各部位,零件是否有松动现象,如发现,需修理后方可安装。

1、 Before installation, check all parts of the fully automatic stubble drying machine for any looseness. If found, repair is required before installation.

  二、安装时,打茬机跑车轮与道轨间隙以打茬机与轨迹来回跑动时为规范。

2、 During installation, the gap between the running wheels of the stubble trimmer and the track is standardized when the stubble trimmer runs back and forth with the track.

  三、打茬机安装结束后,需要行试工作五分钟左右,查看各部位是否有杂音现象出现,如发现杂音应泊车检修,待试工作正常后,方可投入正常生产运用。

20231114111944480.jpg

3、 After the installation of the stubble cutting machine is completed, it needs to be tested for about five minutes to check for any noise in various parts. If any noise is found, it should be parked for maintenance. Only after the test work is normal can it be put into normal production and use.

  四、运用过程中,应经常留意有无异常动静,轰动是否加大,如发现杂音应及时泊车检修。

4、 During use, regular attention should be paid to any abnormal movements and whether the noise increases. If any noise is found, the car should be parked for maintenance in a timely manner.

  五、打茬机投入运用后,应定期查看螺栓有无松动,零部件有无损坏,如发现应根据具体情况检修或更换零部件。

5、 After the stubble cutting machine is put into use, it should be regularly checked for loose bolts and damaged parts. If found, it should be repaired or replaced according to the specific situation.

  六、在运用过程中,注油部位应定期注油,一般每三个月注黄油一次,以确保打茬机各传动部位润滑正常,减少磨损。

6、 During use, the oil injection area should be regularly lubricated, usually with butter every three months, to ensure normal lubrication of all transmission parts of the stubble machine and reduce wear.

  七、全自动晾茬机若长时间停用从头投入生产运用时,要从头进行查看,并通过试车工作正常后再投入生产运用。

7、 If the fully automatic stubble drying machine is stopped for a long time and put into production again, it should be checked from the beginning and put into production again after passing the test run and working normally.

  本文来自:全自动凉茬机 更多的内容请点击:http://www.qfrtrq.com 我们将会为您提问的问题提供一个满意的服务,欢迎您的来电!

This article comes from: Fully automatic stubble cooler. For more information, please click: http://www.qfrtrq.com We will provide satisfactory service for the questions you ask. Welcome to call us!


咨询热线:
0537-4556677