自动凉茬机是将摊晾、加浆、加曲、搅拌、卸料等工序一次性完成，与传统工艺相比，大大降低劳动强度，实现机械自动化。如何稳定使用呢？下面小编为您讲讲。

The automatic stubble cooling machine completes the processes of spreading, adding pulp, adding koji, stirring, and unloading in one go. Compared with traditional processes, it greatly reduces labor intensity and achieves mechanical automation. How to use it stably? Below, the editor will explain to you.

一、安装前应查看自动凉茬机各部位，零件是否有松动现象，如发现，需修理后方可安装。

1、 Before installation, it is necessary to first check all parts of the automatic stubble cooling machine for any looseness. If any looseness is found, it needs to be repaired before installation.

二、安装时，打茬机跑车轮与道轨间隙以打茬机与轨迹来回跑动时为规范。

2、 When installing, the gap between the stubble machine's running wheel and the track is standardized when the stubble machine runs back and forth with the track.

三、打茬机安装结束后，需要行试工作五分钟左右，查看各部位是否有杂音现象出现，如发现杂音应泊车检修，待试工作正常后，方可投入正常生产运用。

3、 After the installation of the stubble cutting machine is completed, it is necessary to conduct a trial operation for about five minutes to check for any noise in various parts. If any noise is found, it should be parked for maintenance. After the trial operation is normal, it can be put into normal production and use.

四、运用过程中，应经常留意有无异常动静，轰动是否加大，如发现杂音应及时泊车检修。

4、 During the use process, it is necessary to regularly pay attention to any abnormal movements and increase the noise. If any noise is found, it should be promptly parked for maintenance.

五、打茬机投入运用后，应定期查看螺栓有无松动，零部件有无损坏，如发现应根据具体情况检修或更换零部件。

5、 After the stubble cutting machine is put into use, it should be regularly checked for looseness of bolts and damage to components. If found, it should be repaired or replaced according to the specific situation.

六、在运用过程中，注油部位应定期注油，一般每三个月注黄油一次，以确保打茬机各传动部位润滑正常，减少磨损。

6、 During operation, the oil injection area should be regularly lubricated, usually with butter every three months, to ensure normal lubrication of all transmission parts of the stubble machine and reduce wear.

七、自动凉茬机若长时间停用从头投入生产运用时，要从头进行查看，并通过试车工作正常后再投入生产运用。

7、 If the automatic stubble cooling machine is stopped for a long time and put into production again, it should be checked from the beginning and put into production again after the test run is normal.

装有多个轴流风机，通过风量的调节，使高温凉茬在输送过程中降到规定的温度，摊晾效果好，在摊晾过程中设置多个搅拌装置，使凉茬在摊晾过程中松散、不易结坨，加浆、下曲均匀，数量可调节，通过装置可将浆水、曲粉、粮茬搅拌均匀。您有需求就来我们网站http://www.qfrtrq.com咨询！

Equipped with multiple axial flow fans, the air volume is adjusted to lower the high-temperature cool stubble to the specified temperature during transportation, resulting in good spreading effect. During the spreading process, multiple mixing devices are set up to make the cool stubble loose and not easy to clump. The addition of slurry and downward bending are uniform, and the quantity can be adjusted. Through the device, the slurry, koji powder, and grain stubble can be evenly mixed. Come to our website if you have any needs http://www.qfrtrq.com consulting service